Compatibility and slots
How to install RAM, step by step
Turn the PC off and unplug it, open the side panel, and check your motherboard manual for which slots to use (usually A2 and B2 for two sticks). Open the slot latches, line up the notch on the stick with the key in the slot, and press straight down firmly on both ends until the latches click. Then close up, power on, and be patient: the first boot with new DDR5 can take a minute or more. It's a 10-minute job that most people get right first time.
What you need
- Your new RAM kit, still in its packaging until you're ready.
- The motherboard manual, printed or open on your phone.
- A clear, well-lit space. A table beats a carpet.
- A flashlight helps inside dark cases.
You don't need tools for the RAM itself; you may need a screwdriver for the side panel. An anti-static wrist strap is nice to have, but touching a bare metal part of the case before you start, and not shuffling around on carpet, does the job for most people.
Step 1: Check what you're installing
Before opening anything, make sure the kit matches your board:
- DDR4 or DDR5? They aren't interchangeable, and the notch is in a different place so the wrong one won't fit. Don't force it.
- Desktop sticks (DIMMs), not laptop ones (SO-DIMMs). Laptop sticks are about half the length.
- One kit, not two separate ones, if you're installing more than two sticks. See can you mix RAM?.
Step 2: Power off and unplug
Shut down Windows, switch off the power supply with the switch on its back, and unplug the power cable. Then press the PC's power button once; this drains leftover power from the board. Lay the case on its side with the motherboard facing up, so you can push down on the sticks without the board flexing sideways.
Step 3: Find the right slots
Look in the manual for "Memory" or "DIMM installation." For two sticks on a four-slot board, it almost always says A2 and B2: the second and fourth slots counting from the CPU. That puts one stick on each memory channel. If you use the two slots next to each other, both sticks share one channel and you lose speed. See dual channel explained.
For four sticks, all slots get filled. On two-slot boards, use both.
Step 4: Remove old sticks, if any
Press the latch (or both latches) at the end of the slot. The stick pops up a little; lift it straight out by the edges. Some boards only have a latch on one end, with a fixed hook at the other. If your graphics card sits right next to the RAM and blocks a latch, you may need to remove the card first.
Step 5: Line up the new stick
Hold the stick by its edges, not the gold contacts. Look at the bottom edge: the notch (a small gap in the gold contacts) sits off-center. Match it to the raised key in the slot. If it doesn't line up, turn the stick around. It only fits one way.
Open the latches on the slot fully before you insert anything.
Step 6: Press it in
Set the stick in the slot, straight up and down. Put your thumbs on the top edge near each end and press firmly and evenly until you hear and feel a click, and the latches close on their own.
This takes more force than most people expect. That's normal, as long as the notch lines up. Press firmly, but if it really won't go, take it out and recheck the notch rather than pushing harder.
Check it's seated: both latches should be closed, the stick should sit at the same height as its neighbor, and you shouldn't see a strip of gold contacts above the slot. A half-seated stick is the most common reason a PC won't start after a RAM upgrade.
Repeat for the other stick.
Step 7: Close up and plug in
Replace the side panel, plug the power cable back in, and switch the power supply on.
Step 8: The first boot (be patient)
New DDR5 has to be "trained": the board tests and adjusts the signal timing for your particular sticks. On the first boot, that can leave the screen black for 30 seconds to several minutes, and the orange "DRAM" light on the board may stay on meanwhile. Don't turn it off. See why DDR5 takes so long to boot.
If nothing happens after five minutes, switch off, reseat each stick firmly, and try again. If it still won't start, try one stick on its own in the slot the manual names for a single stick.
Step 9: Check everything's detected
Once you're in, check that all of your memory shows up:
- The BIOS main screen shows total memory and speed.
- In Windows, open Task Manager → Performance → Memory. It shows the total and "Slots used."
If the total is short by one stick, that stick isn't seated properly or is in the wrong slot.
Step 10: Turn on XMP or EXPO
Your RAM runs at a slow default speed until you enable its profile in the BIOS. This is the step most people forget. See how to enable XMP or EXPO for where the setting is on your board, then check Task Manager shows the speed on the box.
Common mistakes
| Problem | Likely cause |
|---|---|
| PC won't start, DRAM light stays on | Stick not fully seated, or wrong slots |
| Only half the memory shows up | One stick not seated, or a faulty stick |
| RAM runs at 4800 or 5600, not 6000 | XMP or EXPO not turned on |
| PC restarts several times on first boot | Normal memory training; give it time |
| Crashes after enabling XMP | Profile not stable on your setup; see the XMP guide's fixes |
The short version
- Check DDR4 vs DDR5 and that it's desktop RAM before you start.
- Power off, unplug, press the power button, touch the case to discharge static.
- Use slots A2 and B2 for two sticks. Line up the notch, press firmly until it clicks.
- Expect a long first boot. Check the full amount shows in Task Manager.
- Turn on XMP or EXPO, then confirm the speed.