XMP, EXPO and BIOS settings
How to enable XMP or EXPO on ASUS, MSI, Gigabyte and ASRock boards
Restart your PC and press Delete as soon as it powers on to open the BIOS. Find the memory profile setting (XMP on Intel, EXPO on AMD), set it to the first profile, then press F10 to save and restart. The first boot afterward can take a minute or more while the board trains the memory. The exact menu names differ by brand; the table below shows where each one hides it.
Why does this matter?
Out of the box, your RAM runs at a slow, safe standard speed, usually 4800 or 5600 MT/s for DDR5. The faster speed on the box, like 6000, is stored on the sticks as an XMP or EXPO profile, and your board only uses it once you turn it on. Skipping this step is one of the most common reasons a new PC runs slower than it should. See XMP vs EXPO for the background.
Getting into the BIOS
- Restart or power on the PC.
- Tap Delete repeatedly as soon as the screen lights up. On some boards it's F2.
- If the PC boots too fast to catch it, go to Windows Settings → System → Recovery → Advanced startup → Restart now, then Troubleshoot → Advanced options → UEFI Firmware Settings.
Most boards open in a simple screen ("EZ Mode" or "Easy Mode"). The XMP or EXPO switch is often right there. If not, switch to Advanced Mode, usually with F7 (ASUS, MSI) or F2 (Gigabyte).
Where the setting is, brand by brand
| Brand | Easy Mode | Advanced Mode |
|---|---|---|
| ASUS | XMP/EXPO dropdown on the main screen | Ai Tweaker → Ai Overclock Tuner → XMP I, XMP II, EXPO I or EXPO II (older AMD boards say D.O.C.P.) |
| MSI | XMP or EXPO button near the top of the main screen | OC → Extreme Memory Profile (XMP) or EXPO (older AMD boards say A-XMP) |
| Gigabyte (Aorus) | Memory profile switch on the main screen | Tweaker → Extreme Memory Profile (X.M.P.) or EXPO → Profile1 |
| ASRock | Memory profile option on the main screen | OC Tweaker → DRAM Configuration → Load XMP Setting or Load EXPO Setting |
This matches the menu paths G.Skill and Corsair publish for these brands. Names shift a little between board generations, so if you can't find it, your board's manual has a section on memory or "DRAM settings."
Which profile should you pick?
- Most kits have one profile. Pick Profile 1, or the only option shown.
- Kits with two profiles usually store the advertised speed as Profile 1. Pick the one matching the speed on the box.
- ASUS boards show XMP I and XMP II (or EXPO I and II). These aren't two profiles on the sticks; they're two ways of applying one. Skatterbencher explains that the "I" option loads the profile's main timings, speed and voltage and lets the board set the rest, while "II" loads the complete profile exactly as stored. Start with I; if it isn't stable, try II.
- "Tweaked" options on some ASUS and Gigabyte boards apply the profile plus extra tuning from the board maker. They can be a little faster, but try the plain profile first.
Save and restart
Press F10 and confirm. The PC restarts and trains the memory at the new speed.
The first boot can take a while: 30 seconds to a couple of minutes with a black screen is normal for DDR5, and large kits can take longer. Don't switch it off during this. See why DDR5 takes so long to boot, including the setting (Memory Context Restore on AMD) that shortens later boots.
How do you check it worked?
- Task Manager: open it, go to Performance → Memory, and look at "Speed." It should show the rated speed, like 6000 MT/s.
- CPU-Z, Memory tab: "DRAM Frequency" shows half the rated speed, so 3000 MHz for a 6000 kit. That's correct, not a fault.
- The BIOS main screen also shows the current memory speed.
What if it doesn't boot, or crashes?
- Wait first. Give the first boot up to five minutes before deciding it's stuck.
- If it never boots, clear the CMOS (a button on the back of many boards, or a jumper; see the manual). That resets the BIOS to defaults, turning XMP off.
- Update the BIOS. Newer versions usually handle memory better, especially for new kits.
- Check the slots. With two sticks, use the slots the manual recommends, usually A2 and B2 (second and fourth from the CPU).
- Try the other profile option (XMP II instead of I on ASUS), or a speed one step lower than rated.
- Test it. Random crashes after enabling XMP or EXPO usually mean the memory isn't fully stable. Run a memory test such as MemTest86 or TestMem5.
What if there's no XMP option at all?
Most prebuilt PCs from Dell, HP and Lenovo don't have one, so the RAM runs at its standard speed no matter what you buy. That's a BIOS limit, not something you've missed. See how to upgrade RAM in a prebuilt PC.
The short version
- Press Delete at startup, find XMP (Intel) or EXPO (AMD), pick Profile 1, press F10.
- ASUS: Ai Tweaker → Ai Overclock Tuner. MSI: OC tab. Gigabyte: Tweaker. ASRock: OC Tweaker → DRAM Configuration.
- On ASUS, start with XMP I or EXPO I.
- A long, black-screen first boot is normal. Check the speed in Task Manager afterward.
- If it won't boot, clear CMOS, update the BIOS, check the slots, and try again.