Problems and testing

How to check your RAM's speed, timings and chip maker in Windows

For a quick check, open Task Manager: it shows your RAM's speed, how much you have and how many slots are in use. For timings and the exact kit, use the free CPU-Z, and for who made the memory chips themselves, use HWiNFO. None of them change any settings, so they're safe to run.

Why bother checking?

A few common reasons:

  • To confirm XMP or EXPO is on. New DDR5 usually runs at a slower default speed, often 4800 or 5600, until you turn on its profile in the BIOS. Checking takes 30 seconds and catches a very common mistake. See XMP vs EXPO if it isn't.
  • To buy matching RAM. Before adding sticks, you need your current kit's part number and timings. Our guide on mixing RAM explains why.
  • To troubleshoot. If your PC is crashing, knowing the actual speed and voltage helps narrow things down.
  • Curiosity about the chips. Enthusiasts care whether a kit uses SK hynix, Samsung or Micron chips, because it affects overclocking headroom.

Task Manager: the fast check

Press Ctrl+Shift+Esc, click Performance, then Memory. Below the usage graph you'll see:

  • Speed. Your RAM's current data rate, such as 6000.
  • Slots used. For example "2 of 4". That tells you whether you have free slots for an upgrade.
  • Form factor. DIMM for desktop sticks, SODIMM for laptop sticks.
  • Hardware reserved. Memory set aside for things like integrated graphics.

On older versions of Windows the speed is labeled MHz, but the number is really the data rate in MT/s (megatransfers per second). Microsoft started switching the label to MT/s in Windows 11 Insider build 22635.3570 in May 2024, as Tom's Hardware reported, so newer builds show the right unit.

If Speed says 4800 or 5600 on a kit sold as DDR5-6000, your XMP or EXPO profile isn't active. Task Manager doesn't show timings or chip makers, so for anything beyond that, move on to CPU-Z.

CPU-Z: speed, timings and the kit's part number

CPU-Z is a small free tool from CPUID. Download it from CPUID's own site, not a download mirror. Two tabs matter.

The Memory tab shows what your RAM is running at now

  • Type and Size. DDR5, 32 GBytes and so on.
  • DRAM Frequency. This is the real clock, which is half the data rate. DDR5-6000 shows about 3000 MHz here. That's normal, not a fault. Double it to get the MT/s figure.
  • Timings. CAS# Latency (CL), RAS# to CAS# Delay (tRCD), RAS# Precharge (tRP) and Cycle Time (tRAS). A DDR5-6000 CL30 kit running correctly will show 30 for CL. Our guide to RAM timings explains what each one means.
  • Channel #. DDR5 sticks have two small subchannels each, so two sticks often show as "4 x 32-bit". That's still dual channel.

The SPD tab shows what each stick is rated for

SPD is a tiny chip on each stick that stores its specs. Pick a slot from the Memory Slot Selection drop-down and you'll see:

  • Module Manuf. The brand on the box, like G.Skill or Kingston.
  • DRAM Manuf. The company that made the memory chips. More on this below.
  • Part Number. The kit's model code. This is what you search for when buying a matching kit.
  • Week/Year of manufacture, and Ranks (single or dual; see single vs dual rank).
  • A timings table. The left columns are standard JEDEC speeds; the XMP or EXPO columns show the faster profiles stored on the stick, along with their voltage.

An empty slot shows nothing, which is a handy way to check which slots your sticks are actually in.

HWiNFO: the chip maker and more detail

HWiNFO is another free tool, with a lot more detail. Run it in "summary only" mode for a quick look, or open the main window and expand Memory to see each module.

For DDR5, the useful fields include the module's part number, SDRAM Manufacturer (who made the chips) and DRAM Stepping, which is often shown as a die letter such as "A-Die" or "M-Die". HWiNFO's sensor view also shows each DDR5 stick's temperature, which is handy if you're checking for heat problems.

Treat the die letter as a hint, not proof. It comes from what the memory maker wrote into the SPD chip, and on HWiNFO's own forum users have posted kits where the stepping shown didn't match what they expected for that chip. The chip maker field is much more reliable than the die letter.

Can I find out the exact chip (A-die or M-die)?

Not with certainty, without taking the heatsink off and reading the part number printed on the chips. That usually voids the warranty and can damage the stick, so it isn't worth it for most people.

Software gets close enough for most purposes:

  • HWiNFO's DRAM Stepping field, with the caveat above.
  • Thaiphoon Burner, a tool enthusiasts and reviewers use to read the SPD chip in detail. Guru3D used it to identify the SK hynix M-die in a TeamGroup DDR5-6000 kit.
  • A rule of thumb. Overclocking.com noted in 2023 that DDR5 kits rated 6000 to 6400 were mostly SK hynix M-die, and kits from 6600 up were almost all A-die. It called this a generalization, and newer kits vary more, so use it only as a starting guess.

Our guide on Hynix A-die vs M-die vs Samsung vs Micron explains when the chip actually matters. For most people running XMP or EXPO, it doesn't.

Is there a way without installing anything?

Yes, if you're comfortable with PowerShell. Open it and run:

Get-CimInstance Win32_PhysicalMemory | Format-Table BankLabel, Manufacturer, PartNumber, Capacity, Speed, ConfiguredClockSpeed

That lists each stick with its brand, part number and capacity. Speed is the stick's rated default speed, and ConfiguredClockSpeed is what it's running at now. It won't show timings or the chip maker, and some brands fill in the Manufacturer field oddly, so treat it as a quick check rather than the full picture.

What if my RAM shows the wrong speed?

The usual fixes, in order:

  1. Turn on XMP or EXPO in the BIOS. Our step-by-step for ASUS, MSI, Gigabyte and ASRock shows where.
  2. Check you're reading the right number. CPU-Z's DRAM Frequency is half the rated speed by design.
  3. Check for four sticks. On DDR5, four sticks often can't run at their rated speed, and the board may drop them lower.
  4. Update the BIOS if the profile won't stick or the PC won't boot with it on.

If the profile is on and the PC isn't stable, our AM5 instability checklist and RAM testing guide are the next stops.

The short version

  • Task Manager (Ctrl+Shift+Esc, Performance, Memory) shows speed, slots used and form factor.
  • CPU-Z's Memory tab shows live speed and timings; DRAM Frequency is half the rated speed, which is normal.
  • CPU-Z's SPD tab shows each stick's brand, chip maker, part number and XMP or EXPO profiles.
  • HWiNFO shows the chip maker and a die guess. Trust the chip maker more than the die letter.
  • If the speed is 4800 or 5600 on a faster kit, turn on XMP or EXPO.

Sources