Timings

How to manually overclock DDR5 safely (beginner level)

Start from your kit's XMP or EXPO profile, change one thing at a time, and test properly after every change. Keep memory voltage at or below about 1.40V for daily use, and on Ryzen keep the SoC voltage at 1.30V or less. Expect a few percent more performance at best. The easiest wins are tightening one or two main timings and lowering tRFC, not chasing a higher speed.

This guide is for people who've never tuned RAM. It won't get you record numbers, but it won't wreck your Windows install either.

Is it worth doing at all?

Be honest with yourself first. A well-tuned kit might add a few percent in CPU-heavy games, more in your 1% lows, and close to nothing at 4K. Unstable memory, on the other hand, can corrupt files quietly before it ever crashes. If your PC is for work and you can't afford surprises, the XMP or EXPO profile is a fine place to stop.

If you enjoy tinkering and have a free evening, read on.

Before you start

  1. Back up anything important. Memory errors can damage files as they're saved.
  2. Update the BIOS. Newer versions usually train memory better.
  3. Find your reset button. Learn how to clear CMOS on your board (a button on the back panel, or a jumper). If the PC won't start after a change, that gets you back.
  4. Write down your kit's profile. Take a photo of the BIOS timing page with XMP or EXPO on. Those are your safe values.
  5. Find out which chips you have. Different chips tolerate different settings, especially tRFC. See Hynix A-die vs M-die vs Samsung vs Micron.
  6. Get the tools:
    • HWiNFO to watch memory temperature and voltages.
    • ZenTimings (AMD) or the BIOS to read your timings.
    • A memory stress test. TestMem5 with a DDR5 config, Karhu RAM Test (paid) or OCCT's memory test run in Windows. MemTest86 boots from a USB stick.

Safe limits to stay within

Setting Daily limit we'd stay under Why
Memory voltage (VDD, VDDQ) About 1.40V Most XMP and EXPO kits already use 1.25 to 1.40V
SoC voltage (Ryzen 7000/9000) 1.30V AMD's own cap; higher has damaged CPUs
Memory temperature under stress Under about 50°C Tight settings get unstable as DDR5 warms up

Going above these isn't instantly fatal, but it trades lifespan and stability for small gains. Users on the TechPowerUp forums report memory controllers that slowly lost their ability to hold high speeds after months at high SoC voltage, so treat the 1.30V cap as a ceiling, not a target.

Step 1: Load XMP or EXPO and test it

Turn on the profile and run a full memory test, at least an hour of TestMem5 or OCCT. You need a stable starting point. If the stock profile itself throws errors, fix that first: update the BIOS, reseat the sticks, or drop one speed step. There's no point tuning on top of something already unstable.

Step 2: Pick a goal for your platform

  • Ryzen 7000 and 9000: keep the speed at 6000 (or 6200 to 6400 if your CPU holds the controller at 1:1) and work on timings. Running faster than that drops the controller to half speed and usually loses performance. Gear 2 and UCLK explained covers why.
  • Intel 13th/14th gen and Core Ultra: you can try speed first, in steps of 200 MT/s, then tighten timings once you find the highest stable speed.

Step 3: Tighten the main timings

Change one number, test, repeat:

  1. Lower CL by 2 (for example 36 to 34). Run a 20 to 30 minute test. If it passes, try another 2.
  2. Then lower tRCD and tRP by 2 at a time. These often have more room than CL on cheaper kits.
  3. Leave tRAS and tRC on Auto for now. Setting them wrong causes errors and the gain is small.

When a step fails, go back to the last stable value. If CL won't go lower, you can sometimes add 0.02 to 0.05V of memory voltage, staying under the limit above.

Step 4: Lower tRFC

tRFC is how long a memory refresh takes, and nothing else happens on that part of the chip while it runs. Kits ship with it set loosely, so it's often the biggest single gain: Overclockers UK calls lowering tRFC the largest reduction in latency among the secondary timings.

Work in nanoseconds, since the right value depends on your chips, not the speed:

tRFC in ns = tRFC value × 2000 ÷ speed in MT/s

At DDR5-6000, one cycle is a third of a nanosecond, so a value of 600 is 200 ns. EXPO profiles often set it loosely: one popular 6000 CL30 kit uses 884 cycles, about 295 ns. SK hynix chips usually go well below their profile's value, while Samsung and Micron need more. Lower it about 10% at a time, testing after each step, and go back to the last stable value at the first error.

Step 5: Leave the rest alone (for now)

There are dozens more timings, and tREFI in particular can add performance. But tREFI is sensitive to temperature: a setting that's stable on a cool morning can fail in a warm room during a long gaming session. Leave it, and the tertiary timings, until you're comfortable with the basics.

Step 6: Test properly before you trust it

Short tests find big problems. Long tests find the ones that crash your game two hours in.

  • After each small change: 20 to 30 minutes of TestMem5 or OCCT's memory test.
  • When you're done: a long run, a few hours of TestMem5 or Karhu, plus a pass of y-cruncher, which stresses memory and controller together.
  • Then use the PC normally for a week. Random app crashes, browser tabs that die, or Windows file errors are signs something's still off.

On Ryzen, turn Memory Context Restore off while tuning, so the board retrains memory on each boot. Turn it back on once you're done, and test again.

When to stop

Stop when the gains get tiny or the voltages start creeping up. Going from the stock profile to a decent tune is noticeable in benchmarks. Going from a decent tune to a perfect one is a lot of time for very little. Write your final settings down, or save them as a BIOS profile, so a BIOS update or CMOS reset doesn't cost you an evening.

If you're still deciding which kit to buy for tuning, our price charts show which kits are below their usual price right now.

The short version

  • Back up first, update the BIOS, and know how to clear CMOS.
  • Keep memory voltage at or under about 1.40V and Ryzen SoC voltage at or under 1.30V.
  • On Ryzen, stay at 6000 to 6400 and tighten timings. On Intel, try speed first.
  • Change one thing at a time: CL, then tRCD and tRP, then tRFC.
  • Test for hours before you trust it, and stop when the gains get small.

Sources